2012 Heidelberg Stahlfolder KH 78/6 KTL

folding machine

Type: Stahlfolder  KH 78/6 KTL

Manufacturer: Heidelberg

Year: 2012

Max format: 78 x 128 mm

Min format: 14 x 18 mm

Max performance: 230 m/min

Beats/h: 50.000

Standard Equipment

MCT Control System

Modular MCT control system (self-adjustment capability)

Front and rear sheet edge control

Sequential drive control

Automatic speed adjustment on buckle machines via self-adjustment mode

Integrated sheet counter

Speed control for each station

“Tip” mode (slow-speed inching operation)

RFH-82 Drum Feeder

Steel side frames, thickness 10 mm

Ergonomic feeding height – 92 cm

Feed table with transport rollers

Suction wheel with three rows of holes, polyurethane surface

Electromechanical double-sheet detection

Precise sheet alignment using Air Stream Table, without sheet rubbing

1st Station BUH-82

Working width: 82 cm

High-Performance Kit (sheet run monitoring, photocells at entry and exit of 1st station)

6-buckle folding unit (three upper, three lower)

Cast side frames (thickness 25 mm)

Buckle plates with fold-deflecting swing gates

Special Stahl ball bearings with multi-labyrinth sealing and extra-large grease volume

Helical gears for synchronous drive of folding rollers and knife shafts

Automatic lubrication

Folding rollers with soft polyurethane rings

Knife shafts positioned after the buckle plates

GS0 noise-reduction package, including CE safety protection components

Cross Fold Unit KTL

2 folding knives (mounted perpendicular to each other)

Knife shafts after the 1st and 2nd cross fold

Additional buckle plate after the 1st cross fold

Folding rollers with symmetrical opening

Folding rollers and knife shaft run synchronously thanks to enhanced helical-gear transmission

Transport wheels in the knife unit (also in the 3rd and 4th knife units and in the delivery) for improved sheet transport

Electronically controlled knives

Split knife in the cross fold (for small formats)

Optional Accessories

Automation Kit – Feeder: touch-screen operation, electromechanical sheet thickness measurement for automatic roller gap adjustment

Automation Kit Category II – 1st station: automatic adjustment of the gap between folding rollers and knife shafts, motorized buckle plate adjustment

Antistatic Kit (discharging for 1st station: 1× ionizing bar at the infeed of the 1st station, 1× ionizing bar inside the folding station, 1× ionizing bar at the outfeed of the 1st station, including control unit)

Comfort Kit for KTL cross fold unit: adjustment of folding knife angle and height, micro-adjustment of stops, adjustment of transport wheels from outside the machine

Additional Modules

1× head trim (after 2nd cross fold)

1× foot trim (after 2nd cross fold)

2× creasing against PU (metal against PU, after parallel fold)

1× SBP 46.H standing-sheet delivery with pressing unit and separation (single-production mode)

Maximum format: 46 × 30 cm

Minimum format: 12 × 10 cm

Working height: 90 – 110 cm

Load length: max. 80 cm

Infeed width: 46 cm

Automatic adjustment according to signature thickness, automatic return of the stop

1× HSB 34 semi-automatic pressing and banding unit

Maximum format: 34 × 23 cm

Minimum format: 14 × 8 cm

Maximum unpressed pile height: 55 cm

Minimum pressed pile height: 10 cm

Tape width: 1.2 cm

In good condition, fully functional

Find more here - https://www.ucymachines.com/

Contact us at - sales@ucymachines.com

In good condition, fully functional

Find more here - https://www.ucymachines.com/

Contact us at - sales@ucymachines.com